Відео

Make sure you torque to factory specs. Intake manifold bolts are 89 inch pounds and there is s specific sequence to tightening them to guarantee the manifold does not warp. Even the spark plugs have a torque spec. I believe it is 11 ft pounds. You can find the specs/sequence online.

It's pronounced "Riz-Lone", not "Rice-Lone". 🤣

This is why you shouldn't EVER buy a Jaguar (or any other Rover product for that matter).

Excellent instruction! Great videography!

Do those throttle body have gasket fitted in as well.

such a helpful video

Your videos are a godsend🎉

i had a misfiring cylinder and i used the rislone injector cleaner after 75 mles engine was running worste the it finally cleared up

Well done vey helpful

Great video. Couple things to mention. The nuts on top can be very difficult to remove. Harbor freight sells low profile sockets that you can put a wrench on also. This makes the job so much easier. And great advice for removing the heat shield to get that rear bolt. Also keep in mind you cut off old air connector to fit new. Almost impossible to get enough line unless you unclip behind the wheel liner

STOP THE MUSIC

Good job bro 😎

great video

We have a 2014 MK3 Focus Estate 1.6 tdci with the same symptoms of a suspected blown head gasket. Definitely going to source and try this product. So pleased we came across this video.

Thanks for doing an update, my 09 Matrix has the bubbling radiator, and it's throwing misfire codes. It's not overheating and losing very little coolant. I think it's not a terrible leak yet. With 220,000 miles and an excellent tranny, might as well try it.

Hi Mate, in my LR3 TDV6, the light comes on and goes away as soon as I turn on the engine. If I remember correctly, the problem appeared after restoring the left rear wheel which was punctured. Where could the problem be? Tire pressure not the same as the other 3 wheels? Or could there be a leak? Many Thanks. Very good video 💪

Nice job and super cool dogs.

My BMW was jerking hard under full throttle I couldn’t figure out what it was changed coil packs valve cover gasket valve cover. And nothing until i used the chevron fuel cleaner ran it over 40 miles and it fixed the issue

Got some stuttering and response issues rough idle replaced my fuel filter and now imma dump a bottle of that stuff in he kept recommending and see if It makes a difference if it does it will save me a lot of time troubleshooting my intake and spark systems and single out my fuel! Just came to see if these types of things make a difference and can help me figure out what’s going on thank you for the video

very helpful, i had no idea you could get a portable bathtub!! thanks❤

Hasn't come up YET got me :DDDDDDDDDDDDdd

i’ve always wanted to embroider, but i’m so glad i saw this video before i bought a whole new machine! thank you

Thank you so much for your explanation,very simple and understandable!!!

Thanks!

Real talk

Which struts did you use? how did they hold up long term?

10/10

Hi from India, Currently driving a VW TSI car, could only source Chevron Techron Complete system cleaner out of all of them. Could you please tell how is it? Am I good with it?

"DO NOT, BREAK THE TORQUE WITH THE TORQUE WRENCH'! USAALS Instructor

I'm researching how to clean my throttle body right. I appreciate the detail you went into. I'll try not to go crazy with the cleaner and thanks to you I'll make sure I clean the edge, which I haven't heard explicitly on other videos. I am thinking maybe I should take it off after watching the second throttle body cleaning. I'll need to do a bit more research about my exact vehicle to see what all might be involved with that.

watching again..cause another one went bad....best vid!!!!

I just fax a paper facing down will it still go ?

Great job bro! I just picked up 2011 STS and your video caught my eye while I was looking into removal of dash components because I'm going to add nav system mod to gain back up camera. My dash is perfect shape but I still wanted to watch your project. Cheers, Keith

This the best video by far on how to change the brakes on these cars, you helped a lot thanks… now let’s get the back brakes on how to get it in brake service mode

Can you give me a link to where or which part number for these injectors

Thanks so much I broke my small hose too😢

The music is not necessarily

This guy is good

I'm about to pull the air bags off my 2007 range rover sport tdv6 and swap over to raised coilivers had enough of repairing this system the airbags have all been done 2 have gone again and the height sensors don't last long on uk roads they seize up over and over again

Thanks, I have all the systems that you have mentioned, including the Check engine Light. I have loaded the gumout regane hoping that helps with the Lean code that I got...

Why is there no sound?

Great info!!! Thanks!!

Best video Ive seen so far, every detail is explained.

🙏 Sir! Question: Can this test be done with a 12 Volt car battery?

I am a bit confused: It very well explains why disable the height adjustment system. Then at 08:33, height is < 34in and leaning forward and you say that its a leak. Which makes sense. But the conclusion of the video is about replacing the height adjustment system. The only way this would have been a height adjustment system is if overnight the height did not drop but at 08:33 it seems it dropped and indicates a leak.

That is impressive engineering

This is my scenario with gum out. My temp tag is due in a week and my check engine light came on I put half a tank and some gum out last night light turned off. Today is Sunday still off. So tomorrow I do emissions should be good to go in the am woot woot!!

Thanks to your video I was able to change my spark plugs and coils on my own. Local shop wanted $1,700. Only cost about $140 in parts to do on my own.

This was part of the last generation of Epson printers with a good scanner. Sadly new models are so cost reduced that new Epson printers sold today use a DC motor opposed to a Stepper (XP-4200 and ET-2800 still uses a stepper based motor). It makes it worse when the ADF is slow, only single sided and powered only by the scanner motor, used on most models today.

Chilled explanation , thanks